DIY: July 4th Inspired Sandals

DIY: July 4th Sandals

 

 

The Task: Make some cute sandals for the 4th of July 

 

The Ingredients: inexpensive flip-flops (Dollar Tree again), water resistant crazy glue, ribbon, scissors

The Purchase Locations: Dollar Tree

The Cost: Approx. $3.00

It only took me: about 15 minutes

How to:

 

1. Cut the plastic straps off each flip-flop.

 2. Determine how long you want the straps of your sandals. (In hindsight, I wish I had made mine longer so they could wrap around the ankle a few more times.) Cut your ribbon at the desired length.  Fold the ribbon in half and push the loop through the top hole in the flip-flop from the top/front of the flip flop through the back/bottom.

 

3. Turn the flip flop over and tie a big knot or two in the looped part of the ribbon. 

 4. Pull the ribbon down as close to the hole as possible, then add a drop or two of water resistant glue to the hole.  (Be sure to pull the ribbon down first. Otherwise, you'll end up with a sticky ribbon.

 

5. Pull the knot down into the hole and tuck it into the hole so the knot is flush to the bottom of the flip flop (This will keep you from constantly feeling like you are stepping on a rock when you walk).

 

6. Turn the flip flop back over to the top.  You should now have two ribbon "straps".  Yay! 

 

7. Pull the left ribbon strap through the hole on the left bottom of the flip flop.  Then, pull the right ribbon strap through the hole on the right bottom of the flip flop.   Be sure to leave enough ribbon on top so your foot can fit.  (It may be helpful to try the flip flop on while you pull the straps through for accuracy.)

 

8. Turn the flop flip over to the bottom. Take the strap on the left and pull it through the hole on the right from back/bottom to front/top. Take the strap on the right and pull it through the hole on the left from back/bottom to front/top.

 

6. Add a bit of glue to each hole to secure the straps. 

 

7. Repeat these steps with your second flip flop.

 

ENJOY!!

 

Special Thanks to my model: Melissa D. :-)

New Baby Girl...New Sparkly Shoes

These were a gift to a 'new mommy' in my life.

Check out: http://loveleahlynette.blogspot.com/2014/02/diy-sparkly-baby-rhinestone-converse.html for details on how to make these.

This time I added a rhinestone heart to the shoe.  I drew the outline of the heart with a sharpie.  Then, I glued the heart on top of the outline.  And, I added rhinestones all around. 

I also used some cute pink and green ribbon for shoelaces.

ENJOY!!  

Pink Rhinestone Converse Baby Shoes

One night when I couldn't sleep, I made these shoes for my niecy-poo Zylyn.  Probably not the best way to combat insomnia.  But, it was fun. :-)

The Task: Add some pink, sparkly love to the Converse I bought for my niece. 

The Ingredients: shoes, approx. 200 small pink crystal rhinestones (1/4 cm), E6000 glue, a q-tip, Craft Tack, alcohol, a shoe box top

The Purchase Locations: Michael's Arts & Crafts, Downtown LA (for the crystals and shoes), 99 cents only store (for the q-tip and alcohol)

The Cost: Approx. $35.00

It only took me: about two hours

How to:

1.  Where ever you plan to place rhinestones, wipe the area with alcohol.

2. Place a bit of craft tack on the end of a q-tip to create a tool that will allow you to pick up the rhinestones easily.

3. Dump the rhinestones into a shoe box top. I like to lay them out so all the flat sides are down.  This makes them easy to pick up and attach to the shoe.

4. Apply a short, thin line of E6000 glue to the top part of the rubber on the shoe.  Add rhinestones in a line on top of the glue.

5. Repeat step 4 until the entire rubber area (and any other area you want to decorate) is covered in rhinestones.

6. Wipe the rhinestone areas with alcohol after you're done to remove any excess glue from the rhinestones.

OPTION:  You can replace the shoe string with colorful ribbons.

TIPS: Although it is tempting, don't add too much glue at one time.  The glue dries pretty quickly.