DIY: Doggy Princess Tutu...with pearls

DIY: DOGGY PRINCESS TUTU...with PEARLS

The Task: Make a tutu for a doggy princess named Bella. It was her grandpa's birthday and she needed something cute to wear. 

The Ingredients: 1 roll tulle, stretchy ponytail holder or elastic (Bella is extra small so I used the ponytail holder), ribbon, string of pearls, 16 inch long piece of cardboard, glue gun

  

The Purchase Locations: Downtown LA - craft store, jewelry store



The Cost: Approx $6.00

It took me: about 30 minutes 

How to:

1. Take roll of tulle and wrap it long ways around a 16 inch long strip of card board. When all of the tulle has been wrapped around the cardboard, cut the tulle at the top of the cardboard and cut it at the bottom.  Now you have several strips of 16 inch long pieces of tulle.  Repeat this step for each of the rolls of tulle. 

 2. Stretch the ponytail holder around something solid (a piece of cardboard, a book, your knee, whatever) so you can start knotting the tulle around the ponytail holder.  

3. Take two pieces of tulle (one on top of the other) and fold them in half.  Push the looped part up and behind the ponytail holder, then pull the two ends through the loop to create a knot.  Repeat this step until the entire ponytail holder is full. 

4. Tie a ribbon around the middle of the finished tutu. Glue the ribbon to the tutu (I only glued down the part where Bella's tummy was, so her mom and dad could adjust it to fit her waist, as well as get her in and out of it easily).

5. Cut about two-thirds of the tulle off of the stomach area (so your doggy princess can move around easily).

6.  Add a string of pearls to the tutu.  Tie one end of the pearl string to the left side of the tutu, about an inch above where the top of the front left paw would be.  Then, tie the other end of the pearl string to the right side of the tutu, about an inch above where the top of the front right paw would be.  (Because Bella is extra small, the necklace was waaaayy too big.  So, I had to re-string about 20 pearls onto a stretchy piece of string). 

NOTE: I added a little halter ribbon to the tutu thinking it was necessary to hold the tutu in place, but it wasn't necessary. You live and you learn :-)

ENJOY!!

&

HAPPY BIRTHDAY TO BELLA'S GRANDPA!

Love,

Leah Lynette

DIY: July 4th Inspired Sandals

DIY: July 4th Sandals

 

 

The Task: Make some cute sandals for the 4th of July 

 

The Ingredients: inexpensive flip-flops (Dollar Tree again), water resistant crazy glue, ribbon, scissors

The Purchase Locations: Dollar Tree

The Cost: Approx. $3.00

It only took me: about 15 minutes

How to:

 

1. Cut the plastic straps off each flip-flop.

 2. Determine how long you want the straps of your sandals. (In hindsight, I wish I had made mine longer so they could wrap around the ankle a few more times.) Cut your ribbon at the desired length.  Fold the ribbon in half and push the loop through the top hole in the flip-flop from the top/front of the flip flop through the back/bottom.

 

3. Turn the flip flop over and tie a big knot or two in the looped part of the ribbon. 

 4. Pull the ribbon down as close to the hole as possible, then add a drop or two of water resistant glue to the hole.  (Be sure to pull the ribbon down first. Otherwise, you'll end up with a sticky ribbon.

 

5. Pull the knot down into the hole and tuck it into the hole so the knot is flush to the bottom of the flip flop (This will keep you from constantly feeling like you are stepping on a rock when you walk).

 

6. Turn the flip flop back over to the top.  You should now have two ribbon "straps".  Yay! 

 

7. Pull the left ribbon strap through the hole on the left bottom of the flip flop.  Then, pull the right ribbon strap through the hole on the right bottom of the flip flop.   Be sure to leave enough ribbon on top so your foot can fit.  (It may be helpful to try the flip flop on while you pull the straps through for accuracy.)

 

8. Turn the flop flip over to the bottom. Take the strap on the left and pull it through the hole on the right from back/bottom to front/top. Take the strap on the right and pull it through the hole on the left from back/bottom to front/top.

 

6. Add a bit of glue to each hole to secure the straps. 

 

7. Repeat these steps with your second flip flop.

 

ENJOY!!

 

Special Thanks to my model: Melissa D. :-)

DIY: Studded Flip-Flips

DIY: Studded Flip-Flops!!

Summer is coming! Summer is coming!  So, this month I will be featuring a variety of DIY Flip-Flops.  

The Task:  Flippie floppies don't need to be boring OR expensive.  So, grab a pair and spice them up a bit.

The Ingredients: inexpensive flip-flops (got mine from the Dollar Tree), studs, E6000 glue

The Purchase Locations: Dollar Tree, downtown LA rhinestone shop for studs and glue, rubbing alcohol

The Cost: Approx. $3.00

It only took me: about 10 minutes

How to:
1. Wipe off the plastic straps of your flip flops with alcohol.  I do this so the glue will stick better.

2. Decide what pattern you want for your studs.  I just lined them up about 1/4 inch apart from each other.

3. Add a drop of E6000 to the back of one of your studs and place it on the plastic flip flop strap.

4. Repeat until your flip-flops are full of studs and fabulous.

Enjoy!!!

NOTE: I made a pair with raised "bullet" studs.  The studs started to fall off after I wore them a few times.  (I'll post these soon) So, I suggest flatter studs.